Xantech Network Card 283DPRO User Manual

MODEL  
283DPRO  
Professional Visible Emitter  
INSTALLATION INSTRUCTIONS  
BLACK (IR OPAQUE) EMITTER SHIELD  
An optional shield, available from Xantech as model 28DES, fits over  
the emitter head and the sensor window of the controlled component.  
It prevents unwanted external IR signals from passing through or  
leaking past it.  
DESCRIPTION  
The 283DPRO Professional Visible Emitter is a two-piece Emitter.  
Featuring a Designer Emitter, the head-end piece can be attached to any  
electronic component, such as a DVD player. With dressed cables, using  
the included adhesive cable channels, an Emitter can now become part of  
the electronic equipment. The secondary section connects the Designer  
Emitter to a Xantech IR system. Additional lengths for the secondary  
section are available in the 283DPROKIT. The 283DPRO eliminates  
cabling confusion and turns the most complex installation into a  
professional installation.  
Use the 28DES when you want the equipment to respond only to the  
283DPRO, such as in zone controlled systems.  
CONNECTING THE EMITTERS  
Simply insert the mono mini plug of the 283DPRO emitter into the  
“EMITTERS” or “OUT” jacks on any of the Xantech Connecting  
Blocks or Controllers.  
CAUTION: DO NOT plug emitters into the IN/OUT or HIGH OUT  
jacks on the 790-00 and 791-44 Connecting Blocks. To do so will  
destroy the emitters!  
The 283DPRO visible emitter will also indicate the presence of stray  
IR or RF interference by randomly blinking when no IR control signal  
is being sent. Reposition the IR receiver of the interfering source to  
eliminate or reduce the random blinking. The more the random  
blinking is reduced, the better the system will function.  
INSTALLATION  
HEAD-END DESIGNER EMITTER  
SECONDARY CABLE (LENGTH 6 FEET)  
ATTACHING THE EMITTERS TO IR SENSOR WINDOWS  
Each emitter has a clear adhesive layer on the bottom flat surface of  
the shell.  
Simply peel off the adhesive cover and affix the emitter to the center  
of the IR sensor window on the controlled component’s front panel.  
Limited Warranty  
Xantech® warrants its products to be free of defects in materials or  
workmanship. This is a Limited Lifetime warranty from the date of purchase  
by the original consumer. Any products returned to Xantech and found to  
be defective by Xantech within the warranty period will be repaired or  
replaced, at Xantech’s option, at no charge. Xantech will not be  
responsible for the actual cost of installation or removal of the product, nor  
for any incidental or consequential damages. Some states do not allow the  
exclusion or limitation of incidental or consequential damages, so the  
above limitation may not apply to you. This warranty gives you specific  
legal rights. You may have additional legal rights that vary from state to  
state.  
In some cases it may be difficult to find the location of the IR sensor  
on the component. Consult the owner’s manual of the unit, or the  
manufacturer, for the exact IR sensor window location.  
Double-sided adhesive tape is included. If you move the emitter to a  
different component, use this tape to replace the current adhesive  
layer for the best adhesion.  
The shell, though dark in appearance, is transparent to infrared light,  
allowing commands from a handheld remote control to pass through  
it. This permits direct control of the equipment from a handheld  
remote as well as from the 283DPRO.  
Xantech Corporation  
13100 Telfair Ave. 2F, Sylmar CA 91342 | Xantech.com  
Installation Instructions, 283DPRO © 2008 Xantech Corporation  
Document # 08905199X1  
This document is copyright protected. No part of this manual may be  
copied or reproduced in any form without prior written consent from  
Xantech Corporation. Xantech Corporation shall not be liable for  
operational, technical, or editorial errors/omissions made in this document.  
 

Weider Home Gym WESY38730 User Manual
Wharfedale Speaker XR 1000 User Manual
Whirlpool Air Conditioner ATE0942BPP0 User Manual
Whirlpool Freezer RT14DK User Manual
Whirlpool Range 98014840 User Manual
Wizcom Scanner 3 Lite User Manual
Wolf Cooktop CT30IU User Manual
Woodstock Nail Gun W1775 User Manual
Xantrex Technology Portable Generator PV225S 480 P User Manual
Zephyr Ventilation Hood AK8100S User Manual