Xantech Radio 16 Feb User Manual

®
XT1  
AM FM RDS / RBDS Tuner  
User Manual  
1/16  
XT1  
 
Thank you for purchasing the XT1 Tuner. We take great pride in the design and manufacturing  
quality products, and are confident that your new XT1 will provide you with many years of  
enjoyable and trouble-free service. Should you ever have any need to call upon our services,  
please feel free to contact us at the address shown at the end of this manual or contact the dealer  
or distributor from whom you purchased this product. Full details of the warranty coverage provided  
can be found at the end of this booklet.  
Important Safety Instructions  
1. Important! Please read all the safety and operating instructions shown in this manual before  
operating this equipment.  
2. Heed all warnings and follow all operating instructions.  
3. Warning: To assure safety during a lightening storm, the XT1 must be grounded, refer to the  
diagrams on page 4. Also, if the unit is left unattended and unused for long periods of time, it is  
recommended that you unplug the unit from the wall AC outlet.  
4. Locate the product away from heat sources such as stoves, heat sources, radiators or other  
appliances including other amplifiers that produce heat.  
5. Mount the equipment in a wall or cabinet only as described in this owner’s manual.  
6. Do not use this equipment near water, in damp locations, or outdoors.  
3/16  
XT1  
 
Each XT1 package contains  
-
-
-
-
-
-
-
-
-
XT1 AM/FM Tuner with RDS/RBDS  
IR cable: 3.5mm mono socket - 3.5mm stereo jack  
Serial cable: DB9 female - RJ45 male  
Audio Cable: L/R RCA male to 3.5mm stereo female jack  
Audio Cable: L/R RCA male to L/R RCA male  
Power supply 12VDC 300mA  
FM Dipole Antenna  
AM loop antenna  
User Manual  
Optional (sold separately)  
1U Rack mount kit for up to 3 tuners: Xantech part number 1U3XT1RM  
-
FM Antenna  
AM Antenna  
Serial cable to  
3rd party device  
GND  
Power Supply  
3.5mm Mono jack to 3rd  
party IR output  
RS232 control  
The XT1 can be controlled via RS232. To connect a serial control device, the supplied serial cable  
should be used. This cable establishes the RS232 communication to and from the tuner.  
The pin layout and RS232 protocol can be found in the back of this manual.  
IR Receiver input  
To control the XT1 via IR, an IR extender system needs to be used. There is no IR receiver inside the  
LCD display. To connect an industry standard IR extender system, use the supplied IR cable and  
plug the stereo jack of this cable into the IR sensor input of the XT1, and use the mono socket to  
attach the IR extender output to. Tip = IR-SIGNAL, Sleeve = GND.  
Antenna’s  
Position and secure both antennas individually until the clearest sound is heard.  
4/16  
XT1  
 
Front Panel Controls  
1
2
3
4
5
(1) MENU  
Pressing this button allows you access to the following functions:  
-
-
-
-
-
AM/FM band selection  
Auto/Manual tuning selection  
Scan the preset stations  
Memorize a station  
Set the IR Code.  
(2) ENTER (Power)  
When plugging in the power transformer the first time, the tuner will automatically turn on. Pressing this  
button for 4 seconds will turn the unit ON from standby (sleep mode), or put the unit into standby from its  
ON state.  
(3) UP  
Allows for tuning up to higher frequency stations.  
(4) DOWN  
Allows for tuning down to lower frequency stations.  
(5) LCD DISPLAY  
The display will turn off after approximately 3 to 4 minutes. To turn display ON, simply press the ENTER  
button.  
5/16  
XT1  
 
Tuner Operation  
MAKE AM/FM BAND SELECTION  
1. Press and release the MENU button until either the ENTER and MHz characters flash, or the ENTER  
and kHz characters flash.  
2. Press the ENTER button until either MHz or kHz stops flashing.  
3. Press either UP or DOWN button to obtain MHz or kHz. (note – MHz is the FM band and kHz is the  
AM band)  
4. Either wait until the ENTER stops flashing or depress the ENTER button.  
EZ Steps:  
1. Press MENU once  
2. Press ENTER  
3. Press UP  
4. Press ENTER (or wait 3 seconds)  
SELECT AUTO OR MANUAL TUNING  
1. Press and release MENU button until AUTO and ENTER flash.  
2. Press ENTER button to stop flashing.  
3. Press UP or DOWN button to change to a new tuning mode.  
4. Press ENTER to switch to the new mode.  
EZ Steps:  
1. Press MENU twice  
2. Press ENTER  
3. Press UP  
4. Press ENTER (or wait 3 seconds)  
LISTEN TO PRESET STATIONS OR SCANS  
1. Press and release MENU until P-SCAN and ENTER characters flash.  
2. Press ENTER.  
3. Preset stations or scans will continue to advance until the ENTER button is pressed.  
EZ Steps:  
1. Press MENU three times  
2. Press ENTER  
3. When desired station is playing, press ENTER  
NOTE. Although the display only shows frequency steps of 0.1MHz, the actual tuning is done with  
steps of 0.05Mhz. (in EU mode only)  
6/16  
XT1  
 
TO PRESET MEMORIES  
1. Select a desired station.  
2. Press and release MENU button until MEM and ENTER characters flash.  
3. Press ENTER button.  
4. Select desired PRESET number by pressing UP or DOWN button.  
5. Press ENTER button.  
EZ Steps:  
1. Select desired station  
2. Press MENU four times  
3. Press UP or Down  
4. Press ENTER button  
RDS/RBDS INFORMATION  
RDS/RBDS information is not shown on the XT1 display and is only available through its RS232  
connection.  
7/16  
XT1  
 
Xantech Limited Warranty  
Xantech Corporation ("Xantech") warrants to the holder of a valid proof of purchase as the first  
end-user purchaser ("You"), its products to be free from defects in materials and workmanship for  
the periods specified below from the date of purchase. This limited warranty extends only to You for  
product purchased and used in the United States of America. For product purchased outside of the  
United States of America, You must contact the Xantech authorized distributor in your region for  
warranty services. Product is not intended for end user installation. If within the applicable warranty  
period above You discover such item was not as warranted above and You promptly notify  
Xantech in writing, Xantech shall repair or replace the items at its option. Xantech may elect which  
remedy or combination of remedies to provide in its sole discretion. Xantech may use functionally  
equivalent reconditioned/refurbished/pre-owned or new products or parts under this limited  
warranty. This warranty shall not apply (a) to product which shall have been installed by other than  
an authorized Xantech installer, (b) to installed product which is not installed to Xantech's  
specifications, (c) to product which shall have been repaired or altered by others than Xantech, (d)  
to charges for installation or set up or adjustment of customer controls, (e) to product that has  
suffered normal cosmetic deterioration (f) to product which shall have been subjected to  
negligence, misuse, abuse, accident, or damage by circumstances beyond Xantech's control,  
including, but not limited to, lightning, flood, electrical surge, tomado, earthquake, or any other  
catastrophic events beyond Xantech's control, or (g) to product which shall have been subjected  
to improper operation, connected equipment failure or malfunction, inadequate packing or  
shipping damage, maintenance or storage, or to other than normal use of service. The foregoing  
warranties do not cover reimbursement for labor, transportation, shipping, removal, installation, or  
other expenses which may be incurred in connection with repair or replacement. All claims for  
product shipping damage must be processes within 3 days of receipt by You.  
A Xantech Retum Authorization (RA) must be obtained from Xantech by You, your installer or your  
distributor for Product covered under this warranty. Covered product must be sent to Xantech  
together with proof of purchase, RA number, prepaid and insured to Xantech. Freight collect  
shipments will be refused. Risk of loss or damage in transit is borne by the sender. Xantech's warranty  
does not cover Products which have been received improperly packaged, altered, or physically  
damaged. Products will be inspected upon receipt.  
Except as may be expressly provided and authorized in writing by Xantech, Xantech shall not be  
subject to any other obligations or liabilities whatsoever with respect to equipment manufactured or  
sold by Xantech or services rendered by Xantech.  
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED  
WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE.  
ATTENTION: TO OUR VALUED CONSUMERS  
To insure that consumers obtain quality pre-sale and after-sale support and service, Xantech  
products are sold exclusively through authorized dealers and authorized distributors. The warranties  
on Xantech products are NOT VALID if the products have been purchased from an unauthorized  
dealer or distributor. In order to determine if your Xantech re-seller is authorized, please call Xantech  
(800) 843 - 5465.  
8/16  
XT1  
 
Xantech products (go to xantech.com/warranty for model numbers)  
IR Receivers and IR emitters  
Remote Control Switchers  
Modules and Connecting Blocks  
Accessories  
Warranty Duration  
Limited lifetime  
Limited lifetime  
Limited lifetime  
Limited lifetime  
Limited lifetime  
5 year limited  
2 year limited  
2 year limited  
2 year limited  
1 year limited  
1 year limited  
1 year limited  
Speakers  
Volume Controls and Speaker Selectors  
MRC, BX, ZPR and Commercial Products  
Amplifiers  
Control Interfaces  
Hand Held Remote Controls  
SPLCD Product  
Source Components (includes XT1)  
Specifications  
FM  
Frequency Range:  
88 to 108 MHz (US)  
87.5 to 108 MHz (EU)  
75 ohm  
- 5 dBu (typical)  
62 dB A  
Antenna Input Impedance:  
Usable Sensitivity @30dB S/N:  
Signal/Noise ratio - Mono  
- Stereo  
55 dB A  
THD(1kHz)  
- Mono  
- Stereo  
0.2 %  
0.4 %  
Image Rejection:  
79 dB  
Frequency Response:  
Stereo Separation:  
Capture Ratio:  
50 to 15k Hz  
33 dB  
2 dB  
AM  
Frequency Range:  
530 to 1700 kHz (US)  
525 to 1605 kHz (EU)  
23 dBu  
Usable sensitivity:  
IF rejection:  
90 dB  
Selectivity:  
100 dB  
Distortion:  
0.5% (typical)  
50 dB A  
50Hz to 3kHz  
12VDC 300 mA  
Signal/Noise ratio:  
Frequency Response:  
Power requirement:  
AC voltage for Power supply :  
USA/Canada  
120V, 60Hz  
230V, 50Hz  
Europe  
Dimensions: 6"(153mm) D x 4"(102mm) W x 1-1/4" (32mm) H.  
9/16  
XT1  
 
Appendix 1  
RS232 Protocol  
Interface  
Baud Rate :  
Data Bits :  
9600  
8
Stop Bit:  
Parity Bit: none  
1
Transmission:  
In ASCII codes  
Format  
<ZoneID><_><ProductID><_><TunerID>_<Command><_><Parameter1><_><Parameter2><_><CR>  
<Zone ID>  
Is number 00 to 99, a "00" selects all zones.  
The maximum number is 99.  
Zone ID is factory set at "0", can be reassigned to other number below 99.  
<Product ID>  
<Tuner ID>  
For the XT1, the factory default setting for product ID is 10  
Is number 00 to 99, a "00" selects all tuners. Default set to 01  
<Command>  
<Parameter1>  
Is 1 to N, N may be in one or multiple digits as defined in the first column in the  
table below  
None, or is 1 to N, N may be in one or multiple digits as defined in the  
"Parameter1" column below  
<Parameter2>  
None, or is 1 to N, N may be in one or multiple digits as defined in the  
"Parameter2" column below  
<_>  
The fields are separated by an underscore "_"  
<CR>  
A character return to terminate the command line  
<Zone ID>  
If multiple XT1 tuners are used in one application, the Zone ID of each tuner shall  
be reassigned with a unique number so that each tuner can be controlled  
individually via the RS232 port. Use command 14 in the following list to program  
a new Zone ID.  
XT1  
Purpose  
Parameter1 Purpose of Parameter1  
Parameter2  
Command  
1
1
Power on/off  
Power off  
2
Power on  
3
Toggle power on/off  
2
1
2
Band switching  
AM  
FM  
3
Toggle between AM/FM  
1 for preset 1, 32 for preset #32  
3
4
1 to N  
87..107  
Preset access  
Direct frequency  
Enter the integal part of a FM frequency  
Enter the 1st or first two digits of an AM  
frequency  
00..95  
00..99  
5..16  
tuning  
10/16  
XT1  
 
5
6
1
2
Auto Memory  
RS232 Output  
Start scan from the current frequency and  
write each station into preset sequentially  
Start scan from FM 87.5MHZ to 107.95 then  
AM 530 to 1690, write each station into preset  
sequentially.  
1
2
3
4
5
Outputs feedback one by one (i.e. on demand)  
Outputs feedback every 0.5 seconds  
Outputs feedback every 1 seconds  
Outputs feedback every 2 seconds  
Outputs feedback every 5 seconds  
Scan up preset number to play each preset for 5  
sec  
7
1
Preset Scan  
Scan Down preset number to play each preset  
for 5 sec  
2
3
4
Stop the preset scan  
Move and stop only once at the next preset of  
higher number  
Move and stop only once at the next preset of  
lower number  
5
1
8
9
Write/Erase a  
preset  
Enter a "0" to erase the current preset shown in  
the display  
2
1
2
3
4
write the frequency into the entered number  
Auto tune up frequency  
01..32  
Up/Down Tuning  
Auto tune Down frequency  
Manual tune up frequency one step  
Manual tune down frequency one step  
Let Tuner received signal control the mode  
Stereo/Mono  
mode  
10  
1
2
Force the tuner into Mono mode reception  
(Stero mode is  
set each time the auto-tuning is engaged)  
Get frequency  
Output in ASCII, the band and frequency  
listening  
Output in ASCII, the preset number that is  
displaying  
Output in ASCII, the current tuning in "auto" or  
"manual"  
Output in ASCII, the current receiving mode in  
"Stereo" or "Mono"  
11*  
1
2
3
4
Get Preset  
number  
Get Tuning mode  
Get Receving  
mode  
Get Operating  
Status  
Output in ASCII, the Frequency Preset number,  
Tuning Mode, Receiving Mode, Zone ID, IR ID,  
and Power status  
5
Purge EEPROM  
Purge the EEPROM and restore it to the default  
setting  
12  
13  
14  
111  
111  
MPU Reset  
Reset the MPU to default settings  
Reserved for  
future use  
11/16  
XT1  
 
Program XT1 Zone  
ID  
Program XT1 Zone ID "number"  
15  
888  
00..99  
00..99  
Return XT1 Zone ID  
222  
666  
444  
Program XT1 Tuner ID "number"  
Return XT1 Tuner ID  
Examples:  
01_10_00_1_1  
Instruct Zone 1 XT1 to power off  
01_10_06_1_2  
Instruct Zone 1 Tuner 6 XT1 to power on  
Instruct zone 1 XT1 to power on if it is off, or power off if it is on  
Zone 12 XT1 to tune into preset #21  
01_10_00_1_3  
12_10_00_3_21  
03_10_00_4_107_50  
03_10_00_4_99_55  
Zone 3 XT1 to tune to FM 107.50 MHZ  
Zone 3 XT1 to tune to FM 99.55 MHZ (The 2nd digit after the decimal is  
50K/step tuning for Europe)  
03_10_00_2_1  
Switch band to AM reception  
03_10_00_4_05_80  
03_10_00_4_10_00_30  
Zone 3 XT1 to tune to AM 580 KHZ  
Zone 3 XT1 to tune to AM 1030 KHZ  
01_10_14_6_1  
01_10_00_6_4  
Returns the RDS information of Tuner 14  
RDS information is fed to third party device every 2 seconds.  
01_10_00_8_0  
01_10_00_8_15  
02_10_00_11_1  
Zone 1 XT1 to empty the preset currently displaying  
Zone 1 XT1 to write the displayed frequency into preset 15  
When in FM 100.05 MHZ, Zone 2 XT1 outputs FM10005 in ASCII string  
When in FM 100.05 MHZ, Zone 2 XT1 outputs a complete set of operating  
02_10_00_11_5  
data  
IFM10005IIPRESET 02IITUNING AUTOIIMODE STEREOIIZONE 02IIIR 1IIPOWER  
ONI  
2_10_00_11_2  
Simply output "21" in ASCII if the current preset listening is 21  
Program XT1 Zone ID TO 12  
Read Zone ID  
00_10_00_15_888_12  
00_10_00_15_222  
00_10_00_15_666_40  
00_10_00_15_444  
Program XT1 Tuner ID TO 40  
Read Tuner ID  
Notes for Programming:  
Each time after sending a command to operate a XT1, always pause for 0.5 sec then send  
command 11 to receive the update data feedbacks from the XT1.  
12/16  
XT1  
 
Pin Layout  
CN12  
5
9
4
8
3
7
2
6
1
RX  
TX  
Circuit Item  
RJ45  
DB9-Male  
DB9-Female  
TX  
RX  
Pin  
Pin  
Pin  
1
2
4
3
2
5
2
3
5
GND  
13/16  
XT1  
 
Appendix 2  
Discrete IR HEX Codes  
The carrier frequency: 38KHz.  
HEX  
Code  
Key  
IR Code  
AM/FM  
90  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0015 0015 0040 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0015 0015  
0040 0015 0040 0015 0040 0015 0040 0015  
On/Off  
Mem  
Auto  
Dir  
60  
98  
F8  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0040 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015 0015 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0015 0015 0040 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0015 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0015 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015 0040 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0015 0015 0040 0015 0040 0015  
0015 0015 0015 0015 0040 0015 0015 0015 0040 0015 0040 0015 0015 0015 0015 0015  
0040 0015 0040 0015 0015 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0040 0015  
0015 0015 0015 0015 0040 0015 0015 0015 0015 0015 0040 0015 0015 0015 0015 0015  
0040 0015 0040 0015 0015 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0015 0015 0040 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015 0040 0015 0015 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
D8  
A8  
32  
B2  
58  
Up  
Down  
Pre-Set  
ST/MO  
14/16  
XT1  
 
0
1
2
3
4
5
6
7
8
9
78  
E8  
48  
68  
02  
12  
20  
40  
A0  
A2  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0015 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0040 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0015 0015 0015 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015 0040 0015 0040 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0040 0015 0015 0015  
0040 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015 0015 0015 0040 0015  
0015 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0040 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0015 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0015 0015 0015 0015 0040 0015  
0015 0015 0015 0015 0040 0015 0015 0015 0040 0015 0040 0015 0040 0015 0015 0015  
0040 0015 0040 0015 0015 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0015 0015 0040 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0015 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0040 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0015 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015  
0000 006D 0000 0021 0156 00AB 0015 0015 0015 0015 0015 0015 0015 0015  
0015 0015 0015 0015 0015 0015 0015 0015 0040 0015 0040 0015 0040 0015 0040 0015  
0040 0015 0040 0015 0040 0015 0040 0015 0015 0015 0015 0015 0040 0015 0015 0015  
0040 0015 0015 0015 0040 0015 0015 0015 0040 0015 0040 0015 0015 0015 0040 0015  
0015 0015 0040 0015 0015 0015 0040 0015  
15/16  
XT1  
 
®
Xantech Corporation  
13100 Telfair Ave., Sylmar CA 91342 | Xantech.com Installation Instructions,  
XT1, XT1E © 2009 Xantech Corporation Document # 08905219B  
This document is copyright protected. No part of this manual may be  
copied or reproduced in any form without prior written consent from  
Xantech Corporation. Xantech Corporation shall not be liable for  
operational, technical, or editorial errors/omissions made in this document.  
Toll Free Number: 800.843.5465 press 2 for Tech Support  
Email: Tech Support - [email protected]  
Version: B  
16/16  
XT1  
 

Weed Eater Trimmer 545186764 User Manual
Wells Waffle Iron BWB 1S User Manual
Well Traveled Living Patio Heater 60262 User Manual
Westcott Camera Accessories 1861 User Manual
Whirlpool Washer Dryer LB5500XK User Manual
White Rodgers Marine Radio 36C21 User Manual
Wolf Oven FHBO User Manual
XM Satellite Radio Stereo System SKYFi3 User Manual
Yamaha Home Theater System AV S70 User Manual
Zanussi Oven ZDC 888 User Manual