Zanussi Washer Dryer ZWF1000M User Manual

ZANUSSI  
User  
Manual  
Washing  
Machine  
ZWF180M  
ZWF1000M  
 
ZANUSSI  
If volatile cleaning fluids are used, care should be  
taken to ensure that the fluid is removed from the  
garment before placing in the machine.  
• Never pull the power supply cable to remove the  
plug from the socket; always take hold of the plug  
itself.  
• Never use the appliance if the power supply cable,  
the control panel, the working surface or the base  
are damaged so that the inside of the washing  
machine is accessible.  
• All packing and transit bolts must be removed  
before use. Serious damage can occur to the  
product and to property if this is not adhered to.  
See relevant section in the user manual.  
• After having installed the appliance, check that it is  
not standing on the inlet and drain hose and the  
worktop is not pressing the electrical supply cable  
against the wall.  
• If the machine is situated on a carpeted floor,  
please adjust the feet in order to allow air to  
circulate freely under the appliance.  
• Always be sure, that there is no water leakage  
from hoses and their connections after the  
installation.  
• If the appliance is installed in a location subject to  
frost, please read the “dangers of freezing” chapter.  
• Any plumbing work required to install this appliance  
should be carried out by a qualified plumber or  
competent person.  
• Any electrical work required to install this appliance  
should be carried out by a qualified electrician or  
competent person.  
Child safety  
• This appliance is not intended for use by person  
(including children) with reduced physical sensory  
or mental capabilities or lack of experience and  
knowledge unless they have been given  
supervision or instruction concerning use of the  
appliance by a person responsible for their safety.  
• Children should be supervised to ensure that they  
do not play with the appliance.  
• The packaging components (e.g. plastic film,  
polystyrene) can be dangerous to children - danger  
of suffocation! - Keep them out of children’s reach!  
• Keep all detergents in a safe place out of children’s  
reach.  
Use  
• This appliance is designed for domestic use. It  
must not be used for purposes other than those for  
which it was designed.  
• Only wash fabrics which are designed to be  
machine washed.Follow the instructions on each  
garment label.  
• Make sure that children or pets do not climb into  
the drum. To prevent children and pets becoming  
trapped inside the drum this machine incorporates  
a special feature.  
• Do not overload the appliance. See the Washing  
Programme Table.  
• Before washing, ensure that all pockets are empty  
and buttons and zips are fastened. Avoid washing  
frayed or torn articles and treat stains such as  
paint, ink, rust, and grass before washing.  
Underwired bras must NOT be machine washed.  
• Garments which have been in contact with volatile  
petroleum products should not be machine  
washed.  
 
3
Product description  
1
2
3
4
5
6
7
8
Dispenser detergent drawer  
Control panel  
2
1
Drain hose  
3
Door  
Main plug  
Plinth  
5
4
Filter cover  
Adjustable feet  
6
7
8
Detergent  
dispenser  
drawer  
Back cabinet  
Quick Guide  
Accessories  
1. Install the washing machine  
2. Load the laundry  
3. Measure out the detergent  
Transport hole  
plugs  
Drain hose  
support  
4. Close the door  
5. Install the drain and inlet hoses  
6. Turn on the water tap  
7. Plug the power supply  
8. Select the desired programme  
9. Press the [start/pause] button  
Inlet hose  
4
 
USSI  
Compartment for liquid additives (fabric  
Detergent dispenser drawer  
softener, starch).  
Compartment for detergent used for prewash and  
soak phase or for stain remover used during the stain  
action phase (if available). The prewash and soak  
detergent is added at the beginning of the wash  
programme. The stain remover is added during the  
stain action phase.  
Follow the product manufacturer’s  
recommendations on quantities to use and do not  
exceed the «MAX» mark in the detergent dispenser  
drawer. Any fabric softener or starching additives  
must be poured into the compartment before  
starting the wash programme.  
Compartment for powder or liquid detergent used  
for main wash. If using liquid detergent pour it just  
before starting the programme.  
Control panel  
ZWF180M  
1
2
3
4
5
Programme selector dial  
1
Turn the selector dial to select the required washing programme.  
OPTIONS button  
In order to get better care of your clothes you can select the:  
Select the economy for cottons and synthetic items lightly or normally soiled. The washing  
temperature will be reduced. You can use the Economy option if you want to wash normally soiled  
laundry and at the same time save energy;  
Select the Intensive option for heavily soiled laundry. The washing cycle intensity will be  
increased and the washing time will be prolonged.  
2
3
Select the PREWASH button option to perform a prewash cycle before the main wash  
phase. The washing time will be prolonged.  
5
 
Washing phases  
The washing phase running is indicated by the corresponding blinking led.  
4
5
«Start/Pause» button, has the start and pause function. When this button is pressed  
continuously, this machine is switched between start and pause.  
ZWF1000M  
1
2
3
4
5
6
Child Lock  
Programme selector dial  
So your clothes have a more efficient and clean wash different wash cycles can be selected  
depending on the users needs.  
1
SPIN SPEED button  
By pressing this button you can change the spin speed of the selected programme or to  
2
3
select No Spin option  
.
OPTIONS buttons  
In order to get better care of your clothes you can select the:  
That is to increase the level of rinse water. Baby Care function can make the rinse performance  
better to protect the baby skin. Except single wash, rinse, drain and spin procedures, the other  
procedures can select Baby Care function.  
This means that there is neither drain nor spin after the final rinse. Less Iron function can be used  
in all procedures except single wash, rinse, drain and spin. To select drain, spin and/or any other  
washing programmes, firstturn the selector dial in position Oandthenselecttherequiredprogramme.  
Only for cottons and synthetic items lightly or normally soiled at a temperature of 40°C or higher.  
The washing time will be prolonged and the washing temperature will be reduced. You can use  
Economy if you want to wash normally soiled laundry and at the same time save energy.  
 
6
ZANUSSI  
Select the Prewash option to perform a prewash cycle before the main wash phase. The  
washing time will be prolonged. Available for cotton programmes.  
4
5
6
Washing phases  
The washing phase running is indicated by the corresponding blinking led.  
«Start/Pause» button, has the start and pause function. When this button is pressed  
continuously, this machine is switched between start and pause.  
7
 
Washing Programmes  
180M  
1000M  
!Energy test program: Cotton 60 intensive  
!Standard Wool program: 40  
!
!
Compulsory  
Optional  
!The parameter in this table are only for  
user’s reference  
8
 
ZANUSSI  
Helpful hints and tips  
Sorting out the laundry  
Ink: depending on the type of ink, moisten the fabric  
first with acetone*, then with acetic acid; treat any  
residual marks on white fabrics with bleach and then  
rinse thoroughly.  
Tar stains: first treat with stain remover, methylated  
spirits or benzine, then rub with detergent paste.  
Detergents and additives  
Good washing results also depend on the choice of  
detergent and use of the correct quantities to avoid  
waste and protect the environment.  
Although biodegradable, detergents contain  
substances which, in large quantities, can upset the  
delicate balance of nature.  
Follow the wash code symbols on each garment label  
and the manufacturer’s washing instructions. Sort the  
laundry as follows: whites, coloureds, synthetics,  
delicates, woollens.  
Before loading the laundry  
Never wash whites and coloureds together. Whites  
may lose their «whiteness» in the wash.  
New coloured items may run in the first wash; they  
should therefore be washed separately the first time.  
Button up pillowcases, close zip fasteners, hooks and  
poppers. Tie any belts or long tapes.  
Remove persistent stains before washing.  
Rub particularly soiled areas with a special detergent  
or detergent paste.  
The choice of detergent will depend on the type of  
fabric (delicates, woollens, cottons, etc.), the colour,  
washing temperature and degree of soiling.  
All commonly available washing machine detergents  
may be used in this appliance:  
Treat curtains with special care. Remove hooks or tie  
them up in a bag or net.  
Removing stains  
Stubborn stains may not be removed by just water  
and detergent. It is therefore advisable to treat them  
prior to washing.  
• powder detergents for all types of fabric  
• powder detergents for delicate fabrics (60°C max)  
and woollens  
• liquid detergents, preferably for low temperature  
wash programmes (60°C max) for all types of fabric,  
or special for woollens only.  
The detergent and any additives must be placed in  
the appropriate compartments of the dispenser  
drawer before starting the wash programme.  
If using liquid detergents, a programme without  
prewash must be selected.  
Your appliance incorporates a recirculation system  
which allows an optimal use of the concentrated  
detergent.  
Follow the product manufacturer’s recommendations  
on quantities to use and do not exceed the «MAX»  
mark in the detergent dispenser drawer.  
Quantity of detergent to be used  
Blood: treat fresh stains with cold water. For dried  
stains, soak overnight in water with a special  
detergent then rub in the soap and water.  
Oil based paint: moisten with benzine stain remover,  
lay the garment on a soft cloth and dab the stain;  
treat several times.  
Dried grease stains: moisten with turpentine, lay the  
garment on a soft surface and dab the stain with the  
fingertips and a cotton cloth.  
Rust: oxalic acid dissolved in hot water or a rust  
removing product used cold. Be careful with rust  
stains which are not recent since the cellulose  
structure will already have been damaged and the  
fabric tends to hole.  
Mould stains: treat with bleach, rinse well (whites  
and fast coloureds only).  
Grass: soap lightly and treat with bleach (whites and  
fast coloureds only).  
The type and quantity of detergent will depend  
on the type of fabric, load size, degree of soiling  
and hardness of the water used.  
Follow the product manufacturers’ instructions  
on quantities to use.  
Use less detergent if:  
• you are washing a small load  
• the laundry is lightly soiled  
• large amounts of foam form during washing.  
Ball point pen and glue: moisten with acetone*, lay  
the garment on a soft cloth and dab the stain.  
Lipstick: moisten with acetone as above, then treat  
stains with methylated spirits. Treat any residual  
marks with bleach.  
Red wine: soak in water and detergent, rinse and  
treat with acetic or citric acid, then rinse. Treat any  
residual marks with bleach.  
*
do not use acetone on artificial silk.  
9
 
Degrees of water hardness  
Water hardness is classified in so-called  
«degrees» of hardness. Information on hardness  
of the water in your area can be obtained from  
the relevant water supply company, or from your  
local authority.  
When the degree of hardness is soft, re-adjust  
the quantity of the detergent.  
First Use  
• Ensure that the electrical and water connections  
comply with the installation instructions.  
• Remove any material from the drum.  
• Run a cotton cycle at the highest temperature  
without any laundry in the machine, to remove any  
manufacturing residue from the drum and tub. Pour  
1/2 a measure of detergent into the main wash  
compartment and start the machine.  
Personalization  
Additional buzzer selection  
appliance. This function remains enabled also when  
the washing machine is not working.  
You can activate it pressing the buttons 3 and 4 for  
There is an additional selectable buzzer feature.  
Press the Prewash button ( ) for three seconds,  
there will be a «beep» and any operation on the  
control panel becomes silent. To restore the buzzer,  
press the Prewash button ( ) for three seconds  
again. Turning the machine off and then on again will  
not change the buzzer state.  
three seconds to activate the safety device  
Now, it will be impossible to change any other  
programme or option.  
.
Child safety lock (only for model ZWF1000M)  
This device permits you to leave the appliance  
unattended so you do not need to worry that children  
might be injured by or cause damage to the  
10  
 
ZANUSSI  
Daily Use  
Load the laundry  
Select the available options by pressing button 2  
for the model ZWF180M and buttons 3 for model  
the ZWF1000M  
When this button is pressed, the corresponding pilot  
light illuminates. When it is pressed again, the pilot  
light goes out.  
Open the door by  
carefully pulling the door  
handle outwards. Place  
the laundry in the drum,  
one item at a time,  
shaking them out as much  
as possible. Close the  
door.  
Select the Prewash option by pressing button 3  
for the model ZWF180M and button 4 for the  
model ZWF1000M.  
When this button is pressed, the corresponding pilot  
light illuminates. When it is pressed again, the pilot  
light goes out.  
Measure out the detergent and the fabric softener  
Pull out the dispenser drawer until it stops. Measure  
out the amount of detergent required, pour it into the  
main wash compartment or in the appropriate  
compartment if the selected programme/option it  
requires (see more details in «Detergent dispenser  
drawer»).  
If required, pour fabric softener into the compartment  
marked (the amount used must not exceed the  
«MAX» mark in the drawer). Close the drawer gently.  
Start the programme by pressing button 5 for  
model the ZWF180M and button 6 for the model  
ZWF1000M  
Press this button to start the selected washing  
programme.  
Altering an option  
It is possible to change some options before the  
programme carries them out.  
Before you make any change, you must pause the  
washing machine by pressing button 5 for ZWF180M  
or 6 for ZWF1000M.  
Select the required programme by means of the  
programme selector dial (1)  
Turn the programme selector dial to the required  
programme.  
The selector dial can be turned either clockwise or  
anticlockwise.  
Change a running programme  
To change a running programme:  
Turn the selector dial to position O to reset the  
programme or to switch the machine off.  
At the end of the programme the selector dial must be  
turned to position O, to switch the machine off.  
Important! If you turn the programme selector dial to  
another programme when the machine is working, the  
machine will not perform the new selected  
programme.  
• turn the programme selector dial to O, select the  
new programme and press button 5 for ZWF180M  
or 6 for ZWF1000M to start the new programme;  
• press button 5 for ZWF180M or 6 for ZWF1000M  
to pause the machine, turn the programme selector  
dial to the new programme and press button 5 or 6  
again.  
The washing water in the tub will be emptied out.  
Select the spin speed or the Rinse Hold option by  
pressing button 2 (only for ZWF1000M)  
When selecting a programme, the appliance  
proposes automatically a suggested spin speed for  
that programme. (See «Washing programmes» for  
the maximum allowed spin speed).  
Press this button repeatedly to change the spin  
speed, if you want your laundry to be spun at a  
different speed. The relevant pilot light illuminates.  
Warning! For safety reasons you are only able to  
change the programme before the heating phase has  
started  
.
Interrupting a programme  
Press the button 5 for ZWF180M or 6 for ZWF1000M.  
to interrupt a programme which is running.  
Press the button again to restart the programme.  
11  
 
Cancelling a programme  
Turn the selector dial to O to cancel a programme  
which is running, and wait few minutes to open the  
door (This is only possible if there is no water in the  
tub).  
At the end of the programme  
The machine stops automatically.  
At the end of the programme, the door is released,  
after few minutes, and can be opened. Turn the  
programme selector dial to O to switch the machine  
off.  
Remove the laundry from the drum and carefully  
check that the drum is empty. If you do not intend to  
carry out another wash, close the water tap. Leave  
the door open to prevent the formation of mildew and  
unpleasant smells.  
Stand-By:  
Once the programme has finished after a few minutes  
the energy saving system will be enabled.  
By pressing any button the appliance will come out of  
the energy saving status.  
12  
 
ZANUSSI  
Care and cleaning  
Warning! You must DISCONNECT the appliance  
from the electricity supply, before you can carry  
out any cleaning or maintenance work.  
Cleaning the pump  
Important!  
According to the soil level within the cycles and the  
frequency of the cycles, you have to inspect and  
clean the filter regularly.  
Descaling  
The water we use normally contains lime. It is a good  
idea to periodically use a water softening powder in  
the machine.  
Do this separately from any laundry washing, and  
according to the softening powder manufacturer's  
instructions.  
The pump should be inspected if:  
• the machine does not empty and/or spin;  
• the machine makes an unusual noise during  
draining due to objects such as safety pins, coins  
etc. blocking the pump.  
This will help to prevent the formation of lime  
deposits.  
Proceed as follows:  
1 disconnect the appliance;  
2 if necessary wait until the water has cooled down.  
External cleaning  
Clean the exterior cabinet of the appliance with soap  
and water only, and then dry thoroughly.  
3
Open the pump  
door. Place a container  
close to the pump to  
collect any spillage.  
Cleaning the dispenser drawer  
The washing powder and additive dispenser drawer  
should be cleaned regularly.  
Press  
1
Pump cover  
4 Gradually unscrew the pump cover to drain out the  
water.  
2
Clean  
Pull out at the same time  
3
5 When no more water comes out, unscrew the  
pump cover and remove it. Always keep a towel  
nearby to dry up spillage of water when removing  
the cover.  
Flush it out under a tap, to remove any traces of  
accumulated powder.  
Cleaning the drawer recess  
Havin  
g removed the drawer,  
use a small brush to  
6 Remove any objects from the pump impeller by  
rotating it.  
clean the recess ensuring  
that all washing powder  
residue is removed from  
the upper and lower part  
of the recess.  
7 Screw the pump cover fully in.  
8 Close the pump door.  
Warning!  
When the appliance is in use and depending on the  
programme selected there can be hot water in the  
pump. Never remove the pump cover during a wash  
cycle, always wait until the appliance has finished the  
cycle, and is empty. When replacing the cover, ensure  
it is securely retightened so as to stop leaks and  
young children being able to remove it.  
Replace the drawer and  
run the rinse programme without any clothes in the  
drum.  
13  
 
If you wash rugs, it is compulsory to inspect and  
clean the filter.  
Frost precaution or emergency emptied out  
If the machine is exposed to temperatures below 0°C  
or if the water is not discharged, proceed as follows.  
1 Pull out the plug from the power socket.  
2 Turn off the water tap.  
Cleaning the water inlet filters  
Important!  
If the appliance doesn't fill, takes too long to fill with  
water, the start button blinks yellow or the display (if  
available) shows the relevant alarm (see chapter  
«What to do if...» for more details), check if the water  
inlet filters are blocked.  
To clean the water inlet filters:  
• Turn off the water tap.  
• Unscrew the hose  
3 Unscrew the inlet hose.  
4 Place a bowl on the floor and place the end of the  
inlet and drain hoses into it. The water should drain  
by gravity into the bowl.  
5 Select and run a draining programme.  
6 Clean the pump if necessary as previously  
described.  
7 Screw the water inlet hose back on.  
8 When you intend to start the machine up again,  
make sure that the room temperature is above  
0°C.  
from the tap.  
• Clean the filter in the  
hose with a stiff brush.  
• Screw the hose back onto the tap. Make sure the  
connection is tight.  
• Unscrew the hose from the machine. Keep a rag  
nearby because some water may flow.  
• Clean the filter in the valve with a stiff brush or with  
the piece of cloth.  
• Screw the hose back to the machine and make sure  
the connection is tight.  
• Turn on the water tap.  
14  
 
ZANUSSI  
What to do if.....  
Certain problems are due to lack of simple  
maintenance or oversights, which can be solved  
easily without calling out an engineer.  
Before contacting your local Service Centre, please  
carry out the checks listed below.  
Possible Cause / Solution  
Malfunction  
Close the washing machine's door.  
Press the Start/Pause button.  
The washing machine does not work  
Water leakage  
Correctly connect the inlet water pipe.  
The spin of the clothes is abnormal  
Reload and distribute the laundry evenly in the drum.  
There is a peculiar smell in the wa-  
shing machine  
Run a washing cycle without any clothes at maximum  
temperature using a biological powder.  
No fault-water is under the visible area.  
No water is visible in the drum  
There is the remaining water in the  
softener's box  
No fault the effect of the softener will not be affected.  
Empty before next use.  
The water-fast component of the non-phosphorus  
detergent will be left on the clothes to form into spot.  
Please select «Rinse&Spin» programme.  
The remaining detergent is left on  
the clothes  
or brush away the fleck after the clothes is dried.  
Turn on the water tap.  
Check the selection of the procedure.  
Check if the water pressure is sufficient.  
Reconnect the water inlet pipe.  
The washing machine does not fill  
Close the washing machine’s door.  
Check if the inlet water pipe is bent or blocked.  
Make sure the end of the drainage pipe is higher  
than the water level inside the machine .  
Please delete or amend this sentence we would not  
recommend for anyone to seal their drainage pipe.  
The washing machine fills and drains  
at the same time.  
Check if the drainage pumps is blocked.  
Check if the drainage pipe is bent or blocked.  
The washing machine does not drain  
Vibration of the washing machine  
Check the height of the drainage nozzle, make  
sure it is 0.6-1 meter high from the bottom of the  
washing machine.  
Level the washing machine.  
Fasten the footing.  
Check if all the delivery bolts have all been removed.  
15  
 
Possible Cause / Solution  
Malfunction  
Check if the amount of detergent is excessive,  
if it is the specialized detergent for the drum  
washing machine.  
Dip one scoop of the softener mixed with 1/2 liter  
of water to the detergent box II.  
Foam spills from the detergent  
drawer  
Reduce the amount of detergent used next time.  
The machine stops when the proce-  
dure has not been finished  
Power failure or water cut.  
The water inside the inner barrel has been drained  
but there is still a small amount of water in the  
drainage pump and pipe. The drainage pump  
continuously work and takes in the air, then there  
wil be noise which is normal situation.  
The drainage pump is noisy during  
operation after the water has been  
drained.  
The washing machine adds water automatically.  
The machine stops for some time  
during the wash procedure.  
There is too much foam the in drain tube, the foam is  
being drained.  
16  
 
ZANUSSI  
Alarm codes  
If the washing machine cannot work normally, a alarm code will appear on the display. Please carry  
out the following checks.  
Status of  
Corresponding  
Indicators  
Alarm  
Code  
Solution  
Description  
Reason  
Restart after the door is closed  
Door is not closed properly.  
Door lock  
problem  
Please call the service number if you experience any  
problems.  
Open the tap or wait till  
Tap is not opened or water  
the water supply  
Water fill problem flows too slowly.  
becomes normal.  
Check inlet valve filter.  
Straighten the water pipe  
Check the other taps in  
the room.  
when washing  
(water fill time  
exceeds 5  
Inlet valve filter is blocked.  
Inlet pipe is twisted.  
If water is not supplied  
minutes)  
Please call the service number if you experience any  
problems.  
Wash and straighten outlet  
hose.  
Outlet hose is blocked or  
twisted  
Drain pump is blocked  
Drain problem  
while washing  
(drain time  
Wash drain pump filter  
exceeds 7 minutes)  
Please call the service number if you experience any  
problems.  
Excessive detergent has  
been used. Wrong detergent  
used.  
Reduce detergent quantity  
Use the detergents suitable  
for washing machine  
Excessive  
Foam  
Detergent used improperly.  
Please call the service number if you experience any  
problems.  
Please call up the service line if there is any other problem.  
17  
 
ZANUSSI  
If you are unable to identify or solve the problem,  
contact our service centre. Before telephoning, make  
a note of the product number, model, serial number  
and purchase date of your machine. The Service  
Centre will require this information.  
Technical data  
ZWF1000M  
ZWF180M  
520  
520  
60kg  
60kg  
2100W  
2100W  
5
7
10  
 
Installation  
Unpacking  
Accurate levelling prevents vibration, noise and  
displacement of the machine during operation. Never  
place cardboard, wood or similar materials under the  
machine to compensate for any unevenness in the  
floor.  
All transit bolts and packing must be removed before  
using the appliance.  
You are advised to keep all transit devices so that  
they can be refitted if the machine ever has to be  
transported again.  
Unscrew the four bolts  
using a spanner.  
Slide out the relevant  
plastic spacers.  
Water inlet  
Caution! This appliance must be connected to a  
cold water supply.  
Fill the holes with the  
corresponding plastic  
plug caps supplied in the  
bag containing the  
Caution! Before connecting up the appliance to  
new pipework or to pipework that has not been  
used for some time, run off a reasonable amount of  
water to flush out any debris that may have collected  
Caution! Do not use the hose from your previous  
appliance to connect to water supply.  
instruction booklet.  
Connect the hose to a tap  
with a 3/4” thread.  
Always use the hose  
supplied with the  
appliance.  
Positioning  
Install the machine on a flat  
hard floor. Make sure that air  
circulation around the machine  
is not impeded by carpets, rugs  
etc. Check that the machine  
does not touch the wall or other  
kitchen units. Level the  
washing machine by raising or  
1
2
lowering the feet. The feet may  
be tight to adjust as they  
incorporate a self locking nut,  
but the machine MUST be level and stable.  
Any necessary adjustment can be made with a  
spanner.  
If necessary, check the  
setting with a spirit level.  
The other end of the inlet hose which connects to the  
appliance can be turned as showed in the picture. Do  
not place the inlet hose downwards. Angle the hose to  
the left or right depending on the position of your  
water tap. Set the hose correctly by loosening the ring  
nut. After positioning the inlet hose, be sure to tighten  
the ring nut again to prevent leaks.  
 
19  
ZANUSSI  
Caution! The inlet hose must not be lengthened. If it  
is too short and you do not wish to move the tap, you  
will have to purchase a new, longer hose specially  
designed for this type of use.  
Water drainage  
The end of the drain hose can be positioned in three  
ways:  
In a sink drain pipe branch.  
This branch must be above the trap so that the bend  
is at least 60 cm above the ground.  
Hooked over the edge  
of a sink using the  
plastic hose guide  
supplied with the  
machine.  
In this case, make sure  
the end cannot come  
unhooked when the  
machine is emptying.  
Caution! This must be secured with a clip.  
Directly into a drain pipe at a height of not less than  
60 cm and not more than 90 cm. The end of the drain  
hose must always be ventilated , i.e. the inside  
diameter of the drain pipe must be larger than the  
outside diameter of the drain hose.  
This could be done by  
tying it to the tap with a piece of string or attaching it  
to the wall.  
Electrical connection  
Information on the electrical connection is given on  
the rating plate on the inner edge of the appliance  
door. Check that your domestic electrical installation  
can take the maximum load required, also taking into  
account any other appliances in use.  
Caution! Should the appliance power supply  
cable need to be replaced, this MUST be carried  
out by a Service Centre.  
The power supply cable must be easily accessible  
after installing the machine.  
Caution! Connect the machine to an earthed  
socket.  
Caution! The manufacturer does not accept any  
responsibility for damage or injury through failure  
to comply with the above safety precaution.  
Environment concerns  
The symbol on the product or on its packaging  
indicates that this product may not be treated as  
household waste. Instead it should be taken to the  
appropriate collection point for the recycling of  
electrical and electronic equipment. By ensuring this  
product is disposed of correctly, you will help prevent  
potential negative consequences for the environment  
and human health, which could otherwise be caused  
by inappropriate waste handling of this product.  
For more detailed information about recycling of this  
product, please contact your local council, your  
household waste disposal service or the shop where  
you purchased the product.  
Packaging materials  
The materials marked with the symbol are recyclable.  
>PE<=polyethylene  
>PS<=polystyrene  
>PP<=polypropylene  
>PAP<=paper  
20  
 
 
ZANUSSI  
 
 
ZANUSSI  
www.zanussi.co.uk  
 
Subject to change without notice  

Wells Gardner Computer Monitor D9300 Series User Manual
Westinghouse Flat Panel Television LTV 20v2 User Manual
Whirlpool Washer Dryer LA5700XP User Manual
Whirlwind Stereo Amplifier DA 2 User Manual
White Lawn Mower 129 826R190 User Manual
Xerox Copier 50XX User Manual
Xpelair Fan WX6 User Manual
Yamaha Musical Instrument B2000 User Manual
Zanussi Cooktop ZE942 User Manual
Zebra Technologies Tablet Accessory 7309 User Manual